Stretch the carpet along one wall, keeping the stretcher perpendicular to the wall. Lift a corner of the carpeting free of the tack strip with a pliers. Mark how much of the door you will need to cut with a pencil and remove it from the door frame again. increments, moving first toward any side wall that has a door. With the waffle side facing up, staple the carpet padding to the floor every 6 inches. But wait overnight for the glue to set before stretching the carpet. Stretch each corner diagonally. Be careful and work slowly to keep your cut accurate. Leave tack strips in place unless rotten or moldy; otherwise, rip them out using a pry bar angled underneath the setting nails and replace them. If you have any pesky floor squeaks, this is the perfect time to take care of them. Wear gloves to protect your hands from the needle-sharp tacks. If carpet buckling occurs in a hallway, follow the same process, but use a knee-kick carpet stretcher instead of a power stretcher, which is too large for most hallways. Wear gloves when handling them or I guarantee you'll have blood on your hands! She has a degree in journalism from the University of Georgia and began writing professionally in 2001. STEP 8 Finally, carefully press the carpeting into the tack strips on both adjoining walls. When you’ve worked out any lumps in your carpet, immediately fasten the section of carpeting to the tack strip. Cut from the backside, leaving the carpet about 1/8 in. Diy landlord damaged carpet repair in 4 causes for loose and buckled carpet carpet stretching wrinkles at a doorway how to stretch carpet … Repeat the process for the opposite wall, followed by the two remaining walls. The most important tool to rent is a “power” carpet stretcher (Photo 8). The cutter is designed to trap the carpet against the woodwork and cut it accurately. How to Get Red Wine, Coffee & Tomato Sauce Stains Out of Carpet. Use a cold chisel or pry bar and mallet to sink nails under toe-kicks. away from the wall. When using a hand saw to trim the door, cut very slowly to avoid splintering. When Mariel's not writing, she can be found swishing her hair on stage with her punk band and managing the ins-and-outs of self-employment. Use a utility knife to cut the padding to fit tightly against the tack strip. The lifespan of a carpet depends on a number of things, but the wrong placement in a door entry could cause your carpet to buckle and unravel faster than it should. Tip: Before you run to the rental store to pick up your carpet stretching tools, have the tack strips installed and the pad stapled down. Place the knee kicker about an inch from the wall and allow the teeth to grip into the carpet. You should feel the carpet stretch and see wrinkles disappear. STEP 3 Brace the power stretcher’s base against a short length of 2×4 in front of the wall where the carpet remains attached. Protect the wall or woodwork by resting the “pushing” end against a short length of 2x4 (see the stretching sequence below). Disclosure: BobVila.com participates in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for publishers to earn fees by linking to Amazon.com and affiliated sites. In fact, this project’s most challenging aspect for the average homeowner is that it requires access to two professional tools: a power stretcher and knee kicker. Use your utility knife to cut the carpet to the size of the room, adding an extra 4 to 6 inches on each side. Pry upward, freeing the corner of the carpet from the tack strips that hold it in place. Once you’ve undone enough of the edge for you to grab the carpet, set down your pliers and tug the carpet by hand away from the wall. Rest the teeth about 6 in. Using the pliers and a flat-head screwdriver, remove any tacks or staples that might secure the carpet to the padding—or a pry bar if they’re stubborn. Turn the tack strip so the small tacks face up, and press it into the adhesive. You'll have to push hard to force the carpet against the wood, otherwise you may cut it too short or long. A yardstick or straightedge placed atop the carpet can help keep the carpet aligned with the baseboard as you slice. Place a straightedge on top of the carpet and cut along the line, using a utility knife to trim off the excess. Cut new tack strips to length with a pair of tin snips. Carpet Care Tips to Make Your Carpet Last. Hunker may earn compensation through affiliate links in this story. Tuck the newly cut edge of the carpet beneath the baseboard, using a 4-inch putty knife. Don't pull the pad through the staples, or it will rip. When you're ready to reinstall the carpet, trim the pad so it rests right next to the tack strips and staple it every 3 in. Kimberly Johnson is a freelance writer whose articles have appeared in various online publications including eHow, Suite101 and Examiner. Over time, heavy foot traffic and repeated carpet cleanings can loosen the carpet fibers, leaving lumps and buckles. or so along the seams and the tack strip (Photo 6). The tools you need are available from a hardware or construction rental store. A new carpet can transform the look of a room, but you might run into trouble if you're trying to install it yourself. If you only need to remove wrinkles, skip all of the business on tacking and re-laying the carpet just use the techniques shown in Photo 8 and the carpet stretching sequences we show. Hold a straightedge on the carpet at the bottom of the wall. Complete DIY projects like a pro! By Jennifer Noonan. Beginning at one end of the built-in, stretch the carpet and then push the carpet backing into the tack strip with your hand. You'll cut off the 3-in. Then cut off all but 3 in. Also use the knee kicker to stretch confined areas where the power carpet stretcher won't fit (Photo 9D). Then, with a press of the handle, the power stretcher extends, pushing the two ends farther apart and stretching the carpet. By creating an account you agree to the Hunker, Laminate Flooring Installed: Finishing Carpet to Laminate Transition, YouTube: Creative Carpet Repair: How to: Carpet to Tile Transition on a Concrete Floor. Before you pull back the pad, pull out all of the staples with a screwdriver and pliers (Photo 2). Sign up for our newsletter! If you have a masonry floor, glue down the carpet padding instead of using staples and wait for it to completely dry. Carpet Maintenance Tips: 3 Quick Carpet Fixes. Dig the staples out of the carpet pad with a screwdriver or needle-nose pliers. Press forward on the knee portion of the tool to stretch the carpet, and use a putty knife to tuck the edge of the carpet into the tack strip down in the floor. of the excess with a utility knife. Mariel Loveland is a small business owner with an editorial background in lifestyle and technology. Center the tape under the adjoining edges of the carpet and turn on your seaming iron. (Work carefully so that you don’t fray the pile fibers too much during the process.) But be careful; it's easy to unravel the fibers. Share this: Click to share on Twitter (Opens in new window) Then, run a vacuum over the entire carpet; hoovering the excess dirt before you start will limit the amount of dust that shakes free while stretching the carpet. Nail them with a hammer and 8d nails, if necessary. This will prevent the carpet from pulling up when you open and close the door. Now you’ve got flat, smooth, safe wall-to-wall to welcome you home again. Stretch the opposite side of the room with the power carpet stretcher. With more or harder kicks, you can “ratchet” the carpet tighter. Installing them is simply a matter of driving the prestarted setting nails into the floor with a hammer. If you have tight areas where the power carpet stretcher won’t fit (spaces less than 3 ft. from adjoining walls), you’ll also need to rent a “knee kicker.” If a carpet cutter is available, rent it, too (Photo 10). Sometimes the carpet unfastens due to humidity, other times from improper installation. away from wall). overlap after stretching, as we show in Photo 10. Resist the urge! A transition strip does exactly what the name implies by covering the location where two types of flooring meet. Tack strips always come in 4 ft. lengths and are available with concrete nails for slabs or standard nails for wooden floors, so be sure to get the right kind. Start stretching beginning about a foot or so behind the point where the carpet was rolled back. Repeat the process along the entire doorway until no portion of the carpet edge remains visible. Cut the strips to length with a tin snips (Photo 4). If the subfloor is made of concrete, use tack strips with concrete nails. Increase the lifespan of your carpet by laying it correctly. Install the gripper edge in the doorway by following the manufacturer's directions.